Illinois Rail Safety Week 2014
There’s a reason every red-blooded American boy wants to be a train conductor or a truck driver: big powerful machines made of iron and steel are cool. Many kids grow out of this stage, the rest either become truck cops, train conductors or truck drivers. It’s no secret the trucking and rail industry do not always see eye-to-eye, but there are times when both industries need to come together for the greater good. One such instance is Illinois Rail Safety Week 2014. The Illinois Truck Enforcement Association is proudly co-sponsoring this event because trucks play a vital role in rail safety. The article this week will explain why.
September 14th-20th, 2014 marks the inaugural year for Illinois Rail Safety Week. The driving force behind the event is the Illinois Association of Chiefs of Police Traffic Safety Committee, on which several ITEA board members serve as well.
Rail safety may seem rather intuitive, but sadly the numbers prove different. Every year, lives are lost, including those of truckers, for failure to follow simple rules at rail crossings.
Time is money. The boss wants it done yesterday. The phone is ringing. That train is moving slow. I got plenty of time. Bam. Tragedy…again.
State Law vs Federal Law
There are truck specific laws at both the state and federal level. Those truckers who operate with CDLs need to be concerned with both! While some laws are similar at both levels, others are specific to their own code. Some state law violations may not be in the federal law, but CDL status could be affected anyhow.
State law requires that any vehicle moving heavy equipment have proper clearance before crossing the railroad tracks. Because much heavy equipment is transported on lowboy trailers, a nine-inch minimum is required before crossing the rails. What is interesting is the definition of “heavy equipment”.
The statute gives several examples: crawler-type tractor, power shovel, derrick or roller. However, it also gives a catchall. If the equipment being operated or moved is designed to travel less than 10mph, the driver must stop the truck between 15 and 50 feet of the crossing to make sure it is clear.
While most minds will immediately think this statute applies exclusively to oversize/overweight permit loads, it does not say that. What about legal weight skid steers, pavers or excavators? Many of these machines do not exceed 10mph and are moved over trucks.
Speaking of permit loads, the Illinois Department of Transportation has something to say about this topic in the 2012 Permit Manual. If you are operating on a valid IDOT permit on an IDOT road, you assume all liability if a problem arises because you did not stop and inspect the rail crossing prior to crossing. The permit may very well route you over the tracks, but you are still responsible. A violation of permit citation could be issued.
Federal law requires all “buses” to stop and look prior to crossing. The Illinois state law is more restrictive. It not only requires all buses, but any second-division vehicle, carrying passengers for-hire, to stop. This includes vehicles designed to carry ten or more people like some stretch limousines, party buses and 15-passenger vans in ride-sharing agreements.
in Part 392.10, the Federal Motor Carrier Safety Regulations delineate a host of hazardous materials which would require the driver to stop the vehicle at a rail crossing. The Illinois state law defers to this list as well. The key here is enforcement scope.
The truck actually has to being carrying the material, not just displaying placards. While a local police officer can just as easily look at a placard and compare it to the list, the proof of the violation rests with the presence of the material. Illinois State Police troopers can inspect a commercial vehicle without cause, but local Illinois officers are limited by procedural case law. Just crossing the tracks without stopping, while displaying placards, is not enough for a search.
Even with automatic transmissions rapidly gaining popularity in commercial vehicles, the standard transmission is still king. If a truck is of the type which is required to stop at railroad crossings, the driver may not shift gears once the approach to the tracks and has begun. He also cannot shift until the entire vehicle has cleared the tracks. This is for good reason. Even the best drivers sometimes miss gears when shifting. If the trucks stalls on the tracks, bad things could happen.
Illinois needs goods shipped by rail and highway transport, and we need it delivered in one piece by alert drivers. Illinois Rail Safety Week
2014 is all about both industries and law enforcement working together for safety.